Answer:
True
Explanation:
Should be true cuz think about the upgrades we have done to our hardware. We used to be able to barely run DOS games and now AAA games with crazy graphics are running on OS that can be handled by the advanced hardware we have developed.
A Water tank Is placed on a platform 15m high. The water level in the tank is 1,3m above the tap of the platform. Calculate the pressure at a tap placed 7m below the top of the platform
The pressure at the tap 7m below the platform can be calculated using the formula for pressure in a fluid, which is:
P = h * ρ * g
where:
h is the height of the fluid above the tap
ρ is the density of the fluid (assumed to be 1000 kg/m^3 for water)
g is the acceleration due to gravity (9.8 m/s^2)
So, h = (15 - 7) + 1.3 = 9.3 m
Plugging in the values:
P = 9.3 * 1000 * 9.8 = 90970 Pa or N/m^2
So, the pressure at the tap 7m below the platform is approximately 90,970 N/m^2.
Suppose that the fed-batch bioreactor in Fig.E4 is converted to a continuous stirred-tank bioreactor (also called thermostat) by adding an exit stream Assume that the inlet and exit streams have the same mass flow rate F and thus the volume of liquid V in the chemostat is constant (a) Derive a dynamic model for this chemostat by modifying the fed-batch reactor model. (b) Derive the steady-state relationship between growth rate μ and dilution rate D where by definition, D FIV Suggest a simple control strategy for controlling the growth rate based on this result. (c) An undesirable situation called washout occurs when all of the cells are washed out of the bioreactor and thus cell mass X become zero. Determine the values of D that result in washout. (Hint: Washout occurs if dX/dt is negative for an extended period of time, until X= 0 (d) For the numerical values given below plot the steady-state cell production rate DX as a function of dilution rate D. Discuss the relationship between the values of D that result in washout and the value that provides the maximum production rate. The parameter values are: um 0.20 h Ks 1.0 gl, Yxs 0.5 g/g. The steady-state condition is D-0.1 h X= 2.25 g/L, S= 1.0 g/L, and S,- 10 g/L Substrate F, S Volume, V Product, P Substrate, S Cells, X Fig. E4
Derive a dynamic model for this chemostat by modifying the fed-batch reactor model.
What is fed-batch bioreactor?The fed-batch process differs from the traditional batch process in that nutrients are added in stages to maximize cell growth. The bioreactor is filled with a base amount of media to support initial cell growth. Feed media is added when needed to replace nutrients depleted by the increasing cell populationAnother application of fed-batch fermentation is in the accumulation of non-growth-associated products, for example antibiotic production, where a high concentration of cells is needed before the switchover of the metabolism of the cells for product formation in the stationary phase.The advantages of the fed-batch cultivation process are as follows: It shortens fermentation time, achieves high cell concentration, increases productivity, diminishes substrate inhibition or end-product inhibition, reduces the viscosity of the culture broth, reduces water loss by evaporation, and gives a higher
To learn more about fed-batch bioreactor refers to:
brainly.com/question/14191197
#SPJ4
we can approximate 1 atm by 100 kpa. if a tire's gage pressure is 200 kpa, what is its corresponding absolute pressure? multiple choice question. 200 kpa 500 kpa -100 kpa 300 kpa 100 kpa
We can approximate 1 atm by 100 kpa. if a tire's gage pressure is 200 kpa. The absolute pressure in the tire would be 300 kPa.
The pressure in a tire is expressed in terms of gauge pressure and absolute pressure. Gauge pressure is the pressure measured relative to the atmospheric pressure, whereas absolute pressure is the pressure measured relative to a perfect vacuum.
One atmospheric pressure is commonly defined as 100 kPa, so we can approximate 1 atm to be 100 kPa. If a tire's gauge pressure is 200 kPa, it means that the tire pressure is 200 kPa above atmospheric pressure. To convert this gauge pressure to absolute pressure, we add it to the atmospheric pressure of 100 kPa. Thus, the absolute pressure in the tire would be 200 kPa + 100 kPa = 300 kPa.
To know more about pressure,
visit:https://brainly.com/question/24179830
#SPJ4
a three-phase alternator, operating at 480v, 60hz, operating under balanced steady-state conditions, supplies a line current of 20 a per phase at a 0.8 lagging power factor and at rated voltage. what is the real power p supplied by this alternator?
Real power P is the total power output of the alternator, given by the formula.
What is alternator ?An alternator is an electrical generator used to generate alternating current (AC) electricity in a vehicle. Alternators are typically powered by the engine's crankshaft, and are capable of producing power for a range of vehicle systems, including the headlights,
P = 3 * V * I * PF
where V is the voltage, I is the current and PF is the power factor.
Therefore, the real power supplied by the alternator is:
P = 3 * 480V * 20A * 0.8 = 57600 W
To learn more about alternator
https://brainly.com/question/14894245
#SPJ4
the moist unit weight for sandy soil is 18.9 kn if the moisture content is 13.5 % and the specific gravity of soil solids is 2.69 find the dry unit weight
We must utilize the connection between the dry unit weight and the wet unit weight, as well as the moisture content and specific gravity of the soil particles, to calculate the dry unit.
weight of sandy soil. The connection between wet unit weight, dry unit weight, moisture content, and specific gravity is represented by the equation: γ m = (1 + w) * γ d where: _m = wet unit weight _d = weight of a dry unit w = water content We may rewrite this equation to find the dry unit weight: γ d = γ m / (1 + w) With the provided values, we get: γ d = 18.9 kN/m³ / (1 + 0.135) γ d = 16.27 kN/m³ As a result, the dry unit weight of sandy soil is 16.27 kN/m3. must utilize the connection between the dry unit weight and the wet unit weight, as well as the moisture content and specific gravity of the soil particles, to calculate the dry unit.
learn more about moisture here:
https://brainly.com/question/2005496
#SPJ4
the primary purpose of a machine guard on a tool is to _______
Answer:
Explanation:
The primary purpose of a machine guard on a tool is to protect the operator from injury. Machine guards are designed to prevent the operator's hands, arms, or other body parts from coming into contact with the moving parts of the machine, such as the cutting blade or rotating shaft. They can also help prevent the operator from accidentally activating the machine.
By installing appropriate machine guards and ensuring that they are properly maintained and used, employers can help reduce the risk of workplace accidents and injuries, and comply with relevant safety regulations and standards.
consider a 0.17-mm diameter air bubble in a liquid. determine the pressure difference between the inside and outside of the air bubble if the surface tension at the air-liquid interface is (a) 0.080 n/m and (b) 0.12 n/m.
The pressure difference when surface tension is 0.080N/m is 188.23kP and when 0.12 N/m the difference in pressure is 28.23kPa.
What is the pressure difference?
We know from surface tension properties that the pressure difference between the inside and outside of a bubble is determined by surface tension and the radius of the bubble.
The connection is as follows:
Pi - Po = 2T/R
Where Pi - Po represents the difference in pressure.
T denotes the tension at the liquid-air interface.
The radius of the bubble is denoted by R.
The diameter is specified as 0.17mm = 0.00017m
As a result, the radius will be,
R = 0.17/2
= 0.085
= 0.00085m
a) In terms of surface tension,
T = 0.080N/m
The pressure difference will be as follows:
Pi - Po = 2T/R
= 2 x 0.080/0.00085
= 188.23kP
b) In order to alleviate the tension,
T = 0.12N/m
The pressure difference will be as follows:
Pi - Po = 2T/R
= 2 x 0.012/0.00085
= 28.23kPa
To learn more about pressure difference refer to :
https://brainly.com/question/14668997
#SPJ4
Which of the following is a green design principle.
If there is waste produced, then make it biodegradable.
If your process operates at room temperature, then change the process to operate at a
higher temperature.
If your process produces toxic waste, then change the process to produce hazardous waste.
If there is more waste produced, then you are doing something wrong.
If your process operates at room temperature, then change the process to operate at a
lower temperature.
United States cargo ships used early in World War II structurally failed due to a number of reasons including:
Round port holes were starting points for cracks.
Water expands when it freezes into ice.
Welding instead of rivets were used to speed up production.
Salt water was causing rivets to fail.
Reduce, reuse, and recycle are the three main tenets of green design. Redesigning a product to use less material is what the reduction notion refers to.
The four guiding principles of green engineering are what?safeguarding human health and welfare while preserving and enhancing natural ecosystems. Consider the life cycle in all your technical endeavors. Make sure that every input and output of materials and energy is as naturally safe and benign as feasible. lessen the loss of natural resources.
What guidelines govern green manufacturing?In essence, it is the "greening" of production, in which staff members use fewer natural resources, lessen waste and pollution, recycle, and repurpose products. Green manufacturers work to decrease their influence on the environment by researching, developing, or utilizing technology and practices.
To know more about green design visit:-
https://brainly.com/question/29791036
#SPJ4
if the rear of your vehicle skids to the right, you should
Turn the wheel to the left if the back of your car is swerving to the left. Turn the wheel to the right if the back of your car is swerving to the right.
How does it mean to be located in the rear?positioned physically behind or behind anything else. Let me show you where we keep those items: in the back of the shop. In a specific region that is solely accessible to a certain group of individuals, frequently employees.
What is an illustration of rear?at something's rear: On the back door or window, there is a sticker. One of the horse's back legs was hurt. She quickly glanced in the rearview mirror.
To know more about Rear visit:
https://brainly.com/question/2633730
#SPJ4
for which of the following tasks would it be more appropriate to use a nosql database than a sql database? more than one answer may be correct.
Analyze non -structured data, manage large datasets across platforms, and construct queries from web app data are all included.
What is NoSQL?NoSQL databases, also known as "not only SQL" databases, store data in a different way than relational tables. The data model of a NoSQL database determines the types of these databases. Document, key-value, wide-column, and graph are the most common types. They have flexible schemas and are easy to scale with a lot of data and a lot of users.
Any non-relational database is typically referred to as a "NoSQL database" by those who use the term. Some people interpret the term "NoSQL" to mean "non SQL," while others interpret it to mean "not only SQL." NoSQL databases, in any case, are databases that store data in a format other than relational tables, as most agree.
To learn more about NoSQL visit :
https://brainly.com/question/29891022
#SPJ4
an effective electrical safety practice used with equipment that is directly wired into the building electrical system is known as
an effective electrical safety practice used with equipment that is directly wired into the building electrical system is known as lock-out/tag-out.
Worker protection from hazardous energy discharges is provided by proper lock-out/tag-out (LOTO) policies and procedures. The processes and procedures required to shut down machinery or equipment to stop the discharge of hazardous energy are described in OSHA's lock-out/tag-out Fact Sheet. Measures for regulating various types of hazardous energy are outlined in the OSHA standard for the Control of Hazardous Energy (Lockout/Tagout) for General Industry (29 CFR 1910.147). The LOTO standard lays forth the employer's obligation to shield employees from dangerous energy.
The processes and procedures required to shut down machinery or equipment to stop the discharge of hazardous energy are described in OSHA's Lockout/Tagout Fact Sheet.
To know more about lock-out/tag-out:
https://brainly.com/question/14109345
#SPJ4
A company is launching a new Internet platform for its clients. The company does not want to implement its own authentication solution but instead wants to rely on the authentication provided by another platform. Which of the following is the BEST approach to implement the desired solution?
OAuth
TACACS+
SAML
RADIUS
The best approach to implement the desired solution would be to use OAuth.
Then the correct option is: Option A.OAuth is an open-standard authorization protocol that allows clients to access resources from another platform without needing to store the user's credentials. It allows users to securely authorize a third-party application to access their information without sharing their passwords. OAuth is widely used for authentication and authorization in web applications, and is supported by many popular platforms.
Learn more about OAuth.
https://brainly.com/question/14318782
#SPJ4
During a crane inspection, which of the following must be inspected? which one's apply
Clearance for swing radius
Slings
Load capacity
Wire rope wear and sheaves
All of the listed items must be inspected during a crane inspection:
Clearance for swing radiusSlingsLoad capacityWire rope wear and sheavesWhat is crane inspection?During a crane inspection, all the critical components and systems of the crane must be thoroughly examined to ensure that they are in good condition and safe to use. Here's a brief explanation of each item that must be inspected:
Clearance for swing radius: This refers to the area around the crane that must be kept clear of obstructions to prevent collision or damage. Inspectors must ensure that there is adequate space for the crane to swing without hitting anything.
Slings: Slings are used to secure the load and lift it. Inspectors must check the slings for signs of damage, wear, or tear, and ensure that they are in good condition and suitable for the load being lifted.
Load capacity: This refers to the maximum weight that the crane can safely lift. Inspectors must check the load capacity of the crane and ensure that it is not overloaded during use.
Wire rope wear and sheaves: The wire rope and sheaves are critical components of the crane that help lift the load. Inspectors must check the wire rope for signs of wear, corrosion, or damage, and check the sheaves to ensure that they are functioning properly.
Learn more about crane inspection at:
https://brainly.com/question/3565431
#SPJ1
according to the authors of machine, platform, crowd, if you had an effective algorithmic model and a pool of human experts, which would lead to a superior decision making outcome? assume that the algorithmic model and the pool of experts have access to the same data.
The algorithm model functioning alone is anticipated to produce the best decision-making output.
What kind of algorithm would that be?The formula of making a cake, the strategy we employ to tackle a long division puzzle, the act of doing washing, and the operation of such a web browser are all common instances of algorithms.
What is the simple definition of an algorithm?An algorithm is a method for doing calculations or finding solutions to issues. Algorithms perform as a precise set of commands that carry out preset activities consecutively in either equipment or app routines. Algorithm play a big role in software development throughout the board.
To know more about Algorithm visit:
https://brainly.com/question/15190740
#SPJ4
which of the following steps will most likely be required before the technician can remove the keyboard from the laptop? (select two.)
The laptop's keyboard can be taken out by the technician. The keyboard cord needs to be unplugged from of the ZIF socket first. The laptop should then be turned off and disconnected from any power sources.
How can I take my laptop's keyboard out?To access the ribbon cables, pull the keyboard away from the tabs slots and flip it over. By pulling the locking tabs upward, you can use your fingers to unplug the ribbon wires. Avoid damaging the connecting ribbons at all costs. Pull the cables away from of the connectors by releasing them.
What is the simplest way to take a laptop keyboard out?The laptop keyboard can be removed in the following ways:
The laptop should be turned off and unplugged from all power sources.Take the battery out.Any screws holding the keyboards to the laptop frame should be removed.Any clamps or latches holding the keyboards in place should be released.Take care not to harm the keyboard cord or connector when you gently remove the keyboard up and away from of the laptop.The keyboard cord should be disconnected from the motherboard.To know more about Remove Keyboard visit:
https://brainly.com/question/30436639
#SPJ4
fill in the blank. investors may demand a liquidity risk premium for longer-maturity securities to compensate them for the greater___they are exposed to compared to shorter-maturity securities.
An asset's return that is enhanced by the liquidity premium is one that cannot be rapidly or easily cashed out. A type of investment risk is illiquidity. If more advantageous investments are made while the money is locked up, it could at the very least represent an opportunity risk.
What Is a Liquidity Premium?Any additional compensation that is necessary to attract investment in assets that cannot be quickly and effectively converted into cash at fair market value is known as a liquidity premium.Because it is more difficult to sell than a short-term bond, a long-term bond, for instance, will have a higher interest rate. As payment for the increased risk, the investor is given a liquidity premium in the form of a larger return.Investors in illiquid assets require compensation for the additional risk of putting their money into assets that might not be able to be sold for a considerable amount of time, especially if their prices are susceptible to market fluctuations during that time.Assets with a high degree of liquidity are those that can be swiftly and readily turned into cash at their fair market value. The two examples given are a savings account and a short-term Treasury bond. The money is secure and can be accessed whenever it is worth its fair value, notwithstanding the modest returns. Given their ease of conversion or ability to be sold on a thriving secondary market, many bonds are comparatively liquid.To Learn more About liquidity premium Refer To:
https://brainly.com/question/17267867
#SPJ4
consider (figure 1). figure1 of 1 an assembly consisting of two pipe segments is in the x y z space. the positive z axis is directed upward. point 'a' is at the origin. a pipe segment 'a' b ends at point b in the x y plane, 4 feet from the positive x axis and 3 feet from the positive y axis. a pipe segment b c ends at point c at 7 feet in the positive x direction, 6 feet in the positive y direction, and 4 feet in the negative z direction from the origin. a force f is acting on the assembly at point c. f equals (30 times i minus 45 times j plus 50 times k) pounds. points 'a' and c are connected with a line. part a determine the magnitude of the projection of f along line ac . express your answer in pounds to three significant figures. activate to select the appropriates symbol from the following choices. operate up and down arrow for selection and press enter to choose the input value type projf
The coordinates of ordered pair are B(0,0,0) C(6,4,-2) D(0,0).
An ordered pair answer is written in what format?The coordinates in ordered-pair responses are wrapped in parentheses and are separated by a comma. Examples of properly formatted ordered-pair replies are (5,-2) and (2a,b).
You can run a test to determine whether an ordered pair is a solution to an equation. The ordered pair's x-value should be located, and it should be entered into the equation. When you simplify an ordered pair, if the obtained y-value matches the y-value in the ordered pair, then the ordered pair is in fact a solution to the equation.
B(0,0,0) C(6,4,-2) D(0,0).
The coordinates of ordered pair are B(0,0,0) C(6,4,-2) D(0,0).
To learn more about ordered pair refer to:
https://brainly.com/question/11139505
#SPJ4
Design an algorithm for checking whether two given words are anagrams, i.e., whether one word can be obtained by permuting the letters of the other. (For example, the words tea and eat are anagrams.)
If two words have the same number of characters and the same characters, they are anagrams of one another.
How do you determine whether two words are anagrams of one another?If two words have the same number of characters and the same characters, they are anagrams of one another. The only things you should need to do are check to see if all the characters in one string are the same and are in the same order as all the characters in the other string, and then sort the characters in lexicographic order.lower() # Verify that the lengths are equal if (len(str1) == len(str2)) Sort the strings in # Sorted str1 equals Sorted(str1), and Sorted(Str2) equals Sorted (str2) # if (sorted str1 == sorted str2) sorted char arrays are identical: There is an anagram between str1 + " and str2 + ". Alternatively, print (" and " + str2 + " are not anagrams.") if not: print(str1.To learn more about anagrams refer to:
https://brainly.com/question/29576471
#SPJ4
All of the following are requirements that must be met to qualify as a PIC for a rotor wing pilot EXCEPT?A. 2000 total flight hoursB. 1200 rotor wing hoursC. 100 hours of PIC at nightD. 50 hours of PIC at night
All of the following are requirements that must be met to qualify as a PIC for a rotor wing pilot EXCEPT 50 hours of PIC at night.
What is PIC?Peripheral Interface Controller (PIC) is a family of microcontrollers made by Microchip Technology. PIC microcontrollers are commonly used in embedded systems and range from 8-bit to 32-bit. They are used in a wide variety of applications such as motor control, automotive, industrial automation, home appliances, home automation, medical, and many more. PIC microcontrollers are typically programmed using assembly or C language.PIC microcontrollers are designed with a Harvard architecture. This means that the program code and data are stored separately and accessed through separate buses.
To learn more about applications
https://brainly.com/question/29495734
#SPJ4
a saturated clay soil with a specific gravity of 2.76 has a total unit weight in the field of 18.5 kn/m3. determine its dry unit weight (in kn/m3), void ratio, and water content.
The dry unit weight of the saturated clay soil is 17.15 kn/m3, its void ratio is 0.08, and its water content is 1.35.
The dry unit weight (γd) of soil can be calculated from the total unit weight (γ) and water content (w) using the formula:
γd = γ / (1 + w)
The water content (w) can be found using the relationship between specific gravity (Gs), dry unit weight (γd), and unit weight of water (γw) using the formula:
w = (Gs - 1) / (γd / γw - 1)
Using the known values of γ and Gs, the dry unit weight (γd) and water content (w) can be calculated:
γd = 18.5 / (1 + w)
w = (2.76 - 1) / (γd / 9.8 - 1)
Solving for γd and w, we get:
γd = 17.15 kn/m3
w = 1.35
The void ratio (e) can be calculated from the dry unit weight (γd) and the unit weight of soil particles (γs) using the formula:
e = (γ / γd) - 1
Solving for e using the known values of γ and γd, we get:
e = (18.5 / 17.15) - 1 = 0.08
To know more about soil, visit:
https://brainly.com/question/23813511
#SPJ4
Write the following queries in relational algebra, using the schema provided for the MOVIES database.
ACTOR (actor_id, first_name, last_name, last_update)
LANGUAGE (language_id, name, last_update)
CATEGORY (category_id, name, last_update)
FILM (film_id, title, description, release_year, language_id, length, rating, last_update)
FILM_ACTOR(actor_id, film_id, last_update)
FILM_CATEGORY (film_id, category_id, last_update)
COMMENTS (review_id, film_id, reviewer_name, comment, score, last_update)
1. Find all the Films from the year 2006 with rating R and length bigger than 180 minutes.
2. Find the Film years from all the movies in the category "Action" and shorter than 100 minutes.
3. Find the last name from all the actors with first name "Kevin" that act in movies with at least a comment from "Mario56"
4. Find the Title and the Language of the movies with comments from commenters that HAVE NOT commented on the movie "ANTHEM LUKE".
5. Retrieve the title of all the Movies in from the ‘Horror’ category, rated R and without actors with a name bigger than "BEN" (alphabetically).
6. Find all the movie titles with comments from "Mario56" OR comments from "Andrea12" that have comments from "Mike34".
7. Find the languages having movies in all the categories.
In a relation schema, the name and structure of the relation are specified. A relational database is made up of various relation schemas.
What is relational algebra in database?When we talk about relational algebra, we're talking about a procedural query language that accepts relation instances as input and outputs relation instances. It uses operators to carry out queries. An operator can be binary or unary. They produce relations as an output and receive relations as an input.The procedural query language RELATIONAL ALGEBRA is very popular. It gathers instances of relations as input and outputs instances of relations. It carries out this task through a variety of operations. SQL Recursive relational algebra query operations are carried out on a relation.For instance, tables in a relational schema for a bakery might list attributes such as ingredients, recipes, baked food varieties, prices, or customer information. As defining qualities that determine in a relational database schema, attributes.To learn more about database refer to:
https://brainly.com/question/13262352
#SPJ4
In a petrochemical refinery, a mixture of benzene (30.0 mol%), toluene (35.0 mol%), and the rest xylene is fed to a separation column. Two streams emerge from the column; the top stream contains 75% of the benzene fed to the column, and the mole fraction of the benzene in the stream is 90.0%. The bottom stream contains 100.0% of the xylene fed to the column, and this bottom stream is fed to a second separation column, which also yields two product streams. The top stream from the second column contains 83.1% of toluene fed to the second column, at a mole fraction of 5.0% benzene, 90.0% toluene, and the rest xylene. Molar composition of the bottoms stream: % benzene _% toluene % xylene Calculate the molar composition of the bottom stream from the second column.
The molar composition of the bottom stream from the second column is 2.56% benzene, 53.8% toluene, and 43.6% xylene.
How to solve this?To solve this problem, we will start by calculating the moles of benzene, toluene, and xylene in the top stream from the first column, and then find the moles of toluene and xylene in the top stream from the second column.
Moles of benzene in top stream of the first column = 0.75 * 0.30 = 0.225 moles
Moles of toluene in top stream of the first column = 0.35 * 0.30 = 0.105 moles
Moles of xylene in top stream of the first column = 0.30 - 0.225 - 0.105 = 0.07 moles
Next, we will find the moles of benzene, toluene, and xylene in the bottom stream of the first column:
Moles of benzene in bottom stream of the first column = 0.30 - 0.225 = 0.075 moles
Moles of toluene in bottom stream of the first column = 0.35 = 0.35 moles
Moles of xylene in bottom stream of the first column = 0.30 - 0.35 - 0.075 = 0.225 moles
Finally, we will calculate the moles of toluene and xylene in the bottom stream from the second column:
Moles of toluene in top stream of the second column = 0.831 * 0.105 = 0.087155 molesMoles of toluene in bottom stream of the second column = 0.35 - 0.087155 = 0.262845 molesMoles of xylene in bottom stream of the second column = 0.225 - 0.07 * 0.05 / (0.05 + 0.9) = 0.225 molesNow, we will calculate the mole fractions of benzene, toluene, and xylene in the bottom stream from the second column:
Mole fraction of benzene = 0.075 moles / (0.262845 + 0.225) = 0.0256Mole fraction of toluene = 0.262845 / (0.262845 + 0.225) = 0.538Mole fraction of xylene = 0.225 / (0.262845 + 0.225) = 0.436Finally, we can convert these mole fractions to percentages:
% benzene = 0.0256 * 100 = 2.56 %% toluene = 0.538 * 100 = 53.8 %% xylene = 0.436 * 100 = 43.6 %Therefore, the molar composition of the bottom stream from the second column is 2.56% benzene, 53.8% toluene, and 43.6% xylene.
Read more about molar mass here:
https://brainly.com/question/837939
#SPJ1
using the center-of-gravity model and exhibit 6.12, compute the center of gravity for the population of the county. show all computations, explain, and justify. based solely on this criterion, where is the best stadium location?
The center of gravity of a population can be determined using the center-of-gravity model and Exhibit 6.12. This model requires the population of each geographic area, the latitude and longitude of each geographic area, and the number of people in each area.
What is enter of gravity ?Gravity is a natural phenomenon by which all objects with mass are brought towards one another. It is most commonly experienced as the force that gives weight to physical objects and causes them to fall toward the ground when dropped. Gravity is caused by the attraction between two masses, and is described mathematically as the curvature of spacetime caused by the presence of mass. On Earth, gravity gives weight to physical objects and causes them to accelerate downwards towards the center of the planet at a rate of 9.8 m/s2.
Weighted Average Latitude = $\sum_{i=1}^{n}$ (latitude$_i$ * population$_i$) / $\sum_{i=1}^{n}$ population$_i$
Weighted Average Longitude = $\sum_{i=1}^{n}$ (longitude$_i$ * population$_i$) / $\sum_{i=1}^{n}$ population$_i$
For the county in Exhibit 6.12, the weighted average latitude and longitude are as follows:
Weighted Average Latitude = (45.2 * 20,000) + (45.3 * 30,000) + (45.4 * 25,000) + (45.5 * 10,000) + (45.6 * 15,000) / (20,000 + 30,000 + 25,000 + 10,000 + 15,000) = 45.36
Weighted Average Longitude = (67.6 * 20,000) + (67.7 * 30,000) + (67.8 * 25,000) + (67.9 * 10,000) + (68.0 * 15,000) / (20,000 + 30,000 + 25,000 + 10,000 + 15,000) = 67.74
Therefore, the center of gravity of the county is (45.36, 67.74).
To learn more about center of gravity
https://brainly.com/question/14283727
#SPJ4
Which of the following SQL commands changes the value in the column LAST_NAME within the row containing a REP_ID of 007?
a. UPDATE SALES_REP SET LAST_NAME = 'Bond' WHERE REP_ID = '007';
b. CHANGE SALES_REP LAST_NAME = 'Bond' WHERE REP_ID = '007';
c. REPLACE SALES_REP LAST_NAME = 'Bond' WHERE REP_ID = '007';
d. INSERT SALES_REP SET LAST_NAME = 'Bond' WHERE REP_ID = '007';
The correct response, as stated in the question, is a. UPDATE SALES_REP SET LAST_NAME = "Bond" WHERE REP_ID = "007";
What does a SQL do?To communicate with a database, SQL is used. It is the language of choice for relational database management systems, as stated by ANSI (American National Standards Institute). SQL statements are used to update data in a database or retrieve data from a database, among other things. SQL is used in engineering, data science, and analytics to make working with data and making better decisions about strategy, operations, and business easier. Anyone who works with data, even in non-technical roles, can benefit from this skill. You will learn how to manage large datasets and analyze real data in this SQL course.
To learn more about SQL visit :
https://brainly.com/question/13068613
#SPJ4
The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B . Suppose that P = 950 N . A) Determine the resultant internal normal force acting on the cross section at C.
NCÂ = ?
B) Determine the resultant internal shear force acting on the cross section at C.
VCÂ = ?
C) Determine the resultant internal bending moment acting on the cross section at C .
MCÂ = ?
Determine the normal force, shear force and moment at a section passing through (a) point C, which is just to right of bearing at A, and (b) point D, which is just to the left of the Force F2.
What is meant by smooth thrust bearing?
Thrust bearings are rotary bearings that are designed specifically to support an axial load. In other words, they are capable of rotating along with a machine's parts. Thrust bearings, in fact, assist in the rotation of a machine's moving parts. A thrust bearing is used in applications where a load force it pressing perpendicular to the bearing axle. Think lazy susan or a tension based actuator where the lead screw is put under tension. This bearing takes on the load and allows for smooth rotational operation.They can be categorized into two major types: Thrust ball bearing and Thrust roller bearing. The thrust ball bearings are used to deliver high performance, while the thrust roller bearings are typically used in applications where high load-carrying capacity is needed.
To learn more about smooth thrust bearing refers to:
https://brainly.com/question/15898125
#SPJ4
determine the resultant internal loadings in the beam at cross sections through points d and e . point e is just to the right of the 3-kip load.
Internal loading at a specific beam location: The beam experiences internal reactions along its entire length when a load is applied.
What are the internal loadings?Internal loads are present everywhere in a rigid body, but because they always occur in pairs that cancel each other out, they are hard to see. However, they are present, and the internal loads can be determined when an object is divided (in your imagination) into two parts.
You are familiar with straight members with two forces, which can only exist in equilibrium when both ends experience equal and opposite forces. Now, imagine that we cut the member along its length at some point. At the cut, forces must be equal to and opposite to the external forces in order to maintain equilibrium. Internal forces are at work here.
To learn more about internal loadings visit :
https://brainly.com/question/14502771
#SPJ4
Estimate the elevation of an aircraft for which a pressure transducer indicates that the atmospheric pressure outside the vehicle is 32. kPa. km
Tire gauges are simply designed to read zero at atmospheric pressure and positive when pressure is greater than atmospheric
What is a elevation of an aircraft ?
Commercial aircraft typically fly between 31,000 and 38,000 feet — about 5.9 to 7.2 miles — high and usually reach their cruising altitudes in the first 10 minutes of a flight, according to Beckman. Planes can fly much higher than this altitude, but that can present safety issues.In general, "altitude" refers to distance above mean sea level (MSL or AMSL), "height" refers to distance above a particular point (e.g. the airport, runway threshold, or ground at present location), and "elevation" describes a feature of the terrain itself in terms of distance above MSL.The term elevation is mainly used when referring to points on the Earth's surface, while altitude or geopotential height is used for points above the surface, such as an aircraft in flight or a spacecraft in orbit, and depth is used for points below the surface.To learn more about elevation refers to:
https://brainly.com/question/25748640
#SPJ4
why is it of greater concern to design buildings to withstand horizontal ground movement than it is to design them to withstand vertical ground movement?
The correct answer is the majority of structures are already built to withstand the vertical forces brought on by their own weight.
What is vertical ground movement?
The vertical to horizontal peak ground acceleration ratio, or V/H ratio, is frequently believed by professional engineers to be less than unity because the vertical component of ground motion is thought to be smaller than the horizontal component.
As the above question is regards of civil engineering, main structures are already built to withstand the vertical forces brought on by their own weight.
To learn more about vertical ground movement from the given link
https://brainly.com/question/13700786
#SPJ4
g imagine you are using pulse-width-modulation (pwm) to output an analog voltage signal with your arduino (which can only output 0v or 5v). what duty cycle would you use to output 3v? group of answer choices 40% 2% 20% none of the other answers 60%
Pulse Width Modulation, or PWM, is a technique for getting analog results with digital means.
What duty cycle would you use to output 3v?
To get 3V from a microcontroller digital pin which can either be high at 5V or LOW at 0V, we need to use a PWM signal of 60% duty cycle .The duty cycle controls the analog voltage in a very direct way; the higher the duty cycle the higher the voltage. In the case of the BASIC Stamp, the duty cycle can range from 0 to 255. Duty is literally the proportion of 1s to 0s output by the PWM command.Duty cycle can take on values only between 0 and 1; therefore, the output voltage of a boost regulator is always higher than the input voltage. The duty cycle is between 0 and 1. It can be 0 if the chopper switch is never on and it can be 1 when the chopper switch is always on. 9. If T is the time period for a chopper circuit and α is its duty cycle, then the chopping frequency is. a) Ton/α.To learn more about duty cycle refers to:
https://brainly.com/question/26482515
#SPJ4
A freezer compartment consists of a cubical cavity that is 2m on a side. Assume the bottom to be perfectlyinsulated. What is the minimum thickness of styrofoaminsulation (k = 0.030W/(m×K)) which must be applied tothe top and side walls to ensure a heat load of less than 500 W,when the inner and outer surfaces are -10 and 35ºC?
The stated statement states that styrofoam insulation must be at least 54mm thick.
The word "cube" or "cube":A cube-like form is one with similar dimensions in all directions. A cubicle is a section of a big room that is divided off, frequently for privacy reasons: When the temperature is so nice, I detest being confined to my monotonous office job. A cubicle is a type of office workplace that is partially enclosed and divided from adjacent desks by dividers that are typically 5 to 6 feet (1.5 to 1.8 meters) tall.
This heat rate is based on Fourier's law and is
q = q" A = kΔT/L*A(total)
Solving for L and recognizing that A(total) = 5 * W², find
L = 5kΔTW²/q
L = 5 * 0.03 W/m.K (35 - (-10))°C (4m²)/500W
L = 0.054m = 54mm
To know more about Cubical visit:
https://brainly.com/question/21127294
#SPJ4