Since the thermal conditions in the kitchen and the oven, in general, fluctuate over time, heat transfer through the walls, door, and top and bottom sections of an oven is temporary in nature.
However, under the worst predicted conditions, such as the oven's highest temperature setting and the kitchen's projected lowest temperature (the so-called "design" conditions), we would examine this issue as a steady heat transmission problem. If the oven's heating element is big enough to maintain the intended temperature setting under the worst case scenario, it is also big enough to do so by cycling on and off under all circumstances.
Since heat will be entering the oven through each of its six sides, heat transfer from the oven will be three-dimensional in nature. Though it can be considered as being one-dimensional, heat transfer through any wall or floor occurs in the direction normal to the surface. Therefore, by assuming that the heat transfer is one-dimensional at each of the four sides as well as the top and bottom portions, as well as by summing the computed values of heat transfers at each surface, this problem can be substantially simplified.
The question is incomplete, it should be:
In order to determine the size of the heating element of a new oven, it is desired to determine the rate of heat transfer through the walls, door, and the top and bottom section of the oven. In your analysis, would you consider this to be a steady or transient heat transfer problem? Also, would you consider the heat transfer to be one-dimensional or multidimensional?
Learn more about heat transfer here: https://brainly.com/question/16055406
#SPJ4
A commuter train accelerates at a rate of 1.35 m/s2. How long does, in seconds, it takes to reach a top (highest) speed of 65.0 km/h, starting from rest. The same train ordinarily decelerates at a rate of 1.7 m/s2. How long, in seconds, does it take to come to a stop from its top speed. What is the speed, in meters per second, of the train 7 seconds after it starts decelerating from its top speed.
Time is calculated by dividing the final speed by the initial speed and the acceleration. Consequently, that is equal to 1.35 meters per second squared times 22.22 meters per second less than 0.
What is Acceleration?This results in 16.5 seconds. It is the amount of time needed for a train to accelerate from a stop to 80 kilometers per hour.
Acceleration: the rate at which the speed and direction of a moving object vary over time. A point or object going straight ahead is accelerated when it accelerates or decelerates. Even if the speed is constant, motion on a circle accelerates because the direction is always shifting.
Acceleration is a vector quantity since it has both a magnitude and a direction. A vector quantity is also velocity. The velocity vector change during a time interval divided by the time interval is the definition of acceleration.
Therefore, Time is calculated by dividing the final speed by the initial speed and the acceleration. Consequently, that is equal to 1.35 meters per second squared times 22.22 meters per second less than 0.
To learn more about acceleration, refer to the link:
https://brainly.com/question/12550364
#SPJ1
The radius of a wheel is 0.900 m. A rope is wound around the outer rim of the wheel. The rope is pulled with a force of magnitude 5.00 N, unwinding the rope and making the wheel spin CCW about its central axis. Ignore the mass of the rope.
What is the angular displacement Δθ, in radians, of the wheel during 1.20 revolution?
Answer:
θ = 2 π N angle subtended in N revolutions (2 π rad / Rev)
θ = 2 π * 1.2 = 2.4 π angle subtended in 1.2 rev
.... had a complicated relationship with European settlers.
Answer:
Explanation:
native americans
Answer:
Going to assume Native Americans
Explanation:
a person is standing on a scale placed on the floor of an elevator. at time t1, the elevator is at rest and the reading on the scale is 500n. at a later time t2, the person is still standing on the scale and the reading on the scale is 400n . based on the scale readings, which of the following statements about the motion of the elevator could be true at time t2 ?
N = (500 =-ma mg m-500 (= 57.02kg 4-8 400-500 =-ma2a (= 100 57.02 1.960 up wood. Therefore, the word "frets down" Therefore, it is moving upward and accelerating slowly.
Which one of the following represents movement?While the velocity of a train set on a long straight is linear, the journey of a planet all around sun and the movement of a clock's minute hand are both circular motions. The only motion that can be considered random is that of a butterfly.
How many different main motions exist?There are numerous distinct motions. Motions are categorised into five classes in Robert's Rules of Procedure Newly Revised (RONR): Main motions, those that, in the absence of another motion, put business before the assembly. The most typical kind of motion is this one.
To know more about acceleration visit:
https://brainly.com/question/12550364
#SPJ4
at which of the following depths will the dry mantle rock at point x begin to melt if its temperature remains the same?
Typically, the mantle rock begins to melt at a depth of between 25 to 35 km below the Earth's surface, depending on the specific conditions.
The depth at which mantle rock begins to melt is determined by its temperature and pressure. At depths greater than about 60 km, the pressure is high enough to stabilize peridotite, the most abundant mantle rock, in its solid state even at temperatures greater than its melting point. However, at depths of about 200 to 400 km, the temperature is high enough to cause partial melting of the mantle rock. This melting is believed to be the source of magma for most volcanic activity on the Earth's surface.
It is important to note that the mantle rock at point x will not begin to melt if its temperature remains the same. The temperature of the mantle increases with depth due to the heat generated by the Earth's interior. Thus, the mantle rock at deeper depths is hotter and more likely to melt than the mantle rock at shallower depths. In addition, the presence of volatile elements such as water, carbon dioxide, and sulfur can lower the melting point of mantle rock and trigger melting at shallower depths.
Learn more about depth here:
https://brainly.com/question/131247
#SPJ4
Complete question:
If the dry mantle rock at point X is brought closer to the surface of the Earth and the temperature stays the same, at what depth will it start to melt?
35 km; 25 km; 18 km; and 12 km
there are three general types of spectra: continuous, emission, and absorption. each is characterized by a different distribution of the wavelengths (i.e., colors) of radiation. sort the images of the three types of spectra into the appropriate bins.
Based on the spectrum images, the categorization is the following: image 1 (continuous spectrum), image 2 and image 5 (absorption spectrum), image 3 and 4 (emission spectrum).
A continuous spectrum contains all light wavelengths within a specific range. Hot, dense light sources, such as stars, emit a practically continuous spectrum of light that travels in all directions and interacts with other things in space.
An absorption spectrum occurs when starlight passes over a cloud of gas. Some of the light is absorbed and the rest is transmitted. The wavelengths of light absorbed are determined by the elements and compounds used. Dark lines or gaps in the spectrum correspond to wavelengths absorbed by the gas in an absorption spectrum.
Starlight can also excite the atoms and molecules within a cloud of gas, causing it to radiate light. The spectrum of light emitted by a gas cloud is determined by its temperature, density, and composition. An emission spectrum is made up of a sequence of colored lines that correspond to the wavelengths of the illuminating gas.
Let's number the images as in the attached picture. Based on the above description, we can conclude:
Continuous spectrum: image 1
Absorption spectrum: image 2 and 5, since there are dark lines or gasp in the spectrum
Emission spectrum: image 3 and 4, since there are several colored lines in dark background.
Learn more about spectrum here:
https://brainly.com/question/19042165
#SPJ4
Help please, giving Brianlest and points!!
Given the circuit information, we can calculate the current and voltages as follows:
IT = VT / (R1 + R2 + Ro)
I1 = IT
I2 = IT
RT = R1 + R2 + Ro
RT = 7 + 7 + 12 = 26 Ohms
So the total resistance of the circuit (RT) is 26 Ohms.
what did you notice about the total momentum before the collision and the total momentum after the collision in each of the above cases
There is a difference in total momentum before collision (3.212) and total momentum after collision (32.007).
The total momentum before and after a collision is conserved in an isolated system, meaning that the total momentum of the objects before the collision is equal to the total momentum of the objects after the collision. This is known as the law of conservation of momentum.
The law of conservation of momentum is a fundamental concept in physics that states that the total momentum of a closed system remains constant, unless acted upon by an external force. This law states that the momentum of an isolated system remains constant, regardless of any internal or external forces. The law of conservation of momentum is a consequence of the law of energy conservation and is a fundamental principle in mechanics, and it applies to both linear and rotational motion.
The law of conservation of momentum can be applied to a wide range of physical systems, including collisions between objects, explosions, and the motion of objects in space. In the case of a collision between two objects, the total momentum of the objects before the collision is equal to the total momentum of the objects after the collision, provided there is no external force acting on the system. This law is used to predict the velocity and direction of objects after a collision, as well as the amount of energy transferred during the collision.
To learn more about Law of conservation of momentumvisit here:
brainly.com/question/24131537
#SPJ4
Complete Question: -
What did you notice about the total momentum before the collision and the total momentum after the collision in each of the above cases?
The principle you should have noted in the previous question is called conservation of momentum. What do you think it means to say something is conserved in the context of physics?
An astronaut is doing a spacewalk on a long tether at 0.1 km away from the International Space Station (mass of 420,000 kg). His spacesuit includes a very sensitive gravitometer, which indicates the gravitational force acting on the astronaut and his spacesuit from the ISS is 7.0 E−7 N. What is the mass of the astronaut in his suit if G = 6.67 E−11 N*m2/kg2?
Group of answer choices
150 kg
200 kg
300 kg
250 kg
The mass of the astronaut is 250 kg.
option D.
What is the mass of the astronaut?
The mass of the astronaut is calculated by applying Newton's law of universal gravitation as follows;
F = ( G Mm ) / ( R² )
where;
G is universal gravitation constantM is the mass of the space stationm is the mass of the astronautR is the distance between the space station and the astronautGMm = FR²
m = ( FR² ) / ( GM )
m = ( 7 x 10⁻⁷ x 100² ) / ( 6.67 x 10⁻¹¹ x 420,000 )
m = 250 kg
Learn more about gravitational force here: https://brainly.com/question/72250
#SPJ1
Car B is traveling a distance d ahead of car A. Both cars are traveling at 60 ft/s when the driver of B suddenly applies the breakes, causing his car to decelerate at 12 ft/s^2. It takes the driver of car A 0.75 s to react. When he applies his brakes, he decelerates at 15 ft/s^2. Determine the minimum distance d between the cars so as to avoid a collision.
The minimum distance between the cars to avoid a collision is 275 ft.
Let's call the minimum distance between the cars "x".
First, let's calculate how far car B travels before it comes to a stop:
d = (v0)/(2 x a) = (3600)/(2 x 12) = 150 ft
Next, let's calculate how far car A travels before it starts to decelerate:
d = v0 x t = 60 x 0.75 = 45 ft
Finally, let's calculate how far car A travels while decelerating:
d = (v0)/(2 x a) = (3600)/(2 x 15) = 80 ft
Adding up all the distances, we get:
x = 150 + 45 + 80 = 275 ft
So the minimum distance between the cars to avoid a collision is 275 ft.
Distance refers to the measurement of the space between two points. It can be expressed in various units, such as meters, feet, kilometers, etc. In physics, distance is often used to calculate speed, velocity, and acceleration, which are important concepts in mechanics and other branches of physics. Distance can also be used to determine the amount of work done by a force, such as gravitational potential energy, which depends on the distance between two objects. Understanding distance is important in many real-world applications, such as navigation, travel, and engineering design.
Learn more about distance:
brainly.com/question/15172156
#SPJ4
a) using the numbered direction arrows shown, indicate (by number) which direction arrow best represents the direction of the quantities listed below. if the quantitiy has zero magnitude or cannot be determined, indicate using the corresponding number listed below.
1. Position vector at D : 3, the vector point to the right and 3 is to the right direction
2. Displacement for D to F: 6 , if we draw a vector from D to F, with D as origin the direction is same as 6
3. 7, change in velocity is VF - VD , VF = VD by magnitude, if we take VD as +ve and VF as -ve the change is -ve (to the left) and arrow 7 is to the left
4. 10, without knowledge of mass we cannot determine the momentum
5. 9. both forces at F and D are equal in magnitude and opposite in direction and hence the magnitude is 0
6. 1, the vector at E and 1 are in the same direction upward.
7. 1, the change is position from D to E same as vector 1, E^ -D^
8. 10, we need to have the magnitudes of VE and VD to know the direction of VE - VD to know the change in velocity from D to E.
9. 10, same as 8, we need to know the magnitudes of velocities and the mass to know the momentum and the change in momentum
10.10, we need to know the magnitudes of force at D and E
Magnitude is a measure of the size or intensity of a physical quantity, such as a force, velocity, or earthquake. In physics, magnitude is used to quantify the relative size of different physical quantities, making it easier to compare and understand their relative importance.
In vector physics, magnitude refers to the length or magnitude of a vector. A vector has both magnitude and direction, and the magnitude of a vector represents its strength or size, while its direction represents the direction in which it acts. The magnitude of a vector can be calculated using mathematical formulas, such as the Pythagorean theorem, which is used to find the length of a right triangle.
To learn more about Magnitudes visit here:
brainly.com/question/28173919
#SPJ4
Complete Question: -
Using the numbered direction arrows shown, indicate (by number) which direction arrow best represents the direction of the quantities listed below. If the quantity has zero magnitude or cannot be determined, indicate using the corresponding number listed below.
The position vector at location D
The change in position (the displacement) between location D and location F
The change in velocity between location D and location F
The change in momentum between location D and location F
The average net force between location D and location F
The position vector at location E
The change in position (the displacement) between location D and location E
The change in velocity between location D and location E
The change in momentum between location D and location E
The average net force between location D and location E
using the graphic map and information provided above, explain how each of the following forces had devolutionary pressure
The king and the president-elect share authority in Spain, a parliamentary monarchy. Spain is one of the most decentralized democracies in Europe, while having a national parliament.
Each of its 17 areas is in charge of running its own public facilities, such as hospitals and schools. Multiculturalism is the nation exhibits diversity in history, race, language, and religion. Economic inequalities by region Spain's many areas display disparity, unequal economic development, and variations in the leading economic activities. Geographical location and territorial scope. Spain's geography includes mountains and aquatic bodies. Additionally, there are geographical variations in the availability or location of natural resources. Additionally, some sections are larger than others.
To learn more about Multiculturalism click here https://brainly.com/question/28327580
#SPJ4
complete question: Using the graphic/map and information provided above, explain how each of the following forces lead to devolutionary pressure within SPAIN.
1. Cultural diversity
2. Regional Economic differences
3. Physical Geography and Territorial size
ohm's law Circuits
Calculate the total Resistance, Current, and Power in the circuits
The total Resistance is 14 ohm, Current is V/14 and Power is V²/14.
R total= R1+R2+R3+R4 = 2+2+6+4= 14ohm
The 4 resistances are connected in series.
Current across R total = I = V/R total = V/14
Power= I. V= V/14 × V= V²/14
About Ohm's lawOhm's law is one of the physics that is quite close to everyday life, because in everyday life, of course, we cannot be separated from electronic devices. As is known, almost all electronic devices require electricity to be turned on or operated. Every electrical device has different voltages, depending on their needs.
When the electricity supplied exceeds the required limit of the device, it is likely that the device will be damaged. Electricity itself appears because basically every object contains two types of charge, namely positive (protons) and negative (electrons). And when the negative charge or electrons move, an electric current will appear.
Learn more about ohms law at https://brainly.com/question/11431009
#SPJ1
an inclined track is secured to a table. the height of the highest point of the track above the tabletop is h1 . the height from the tabletop to the floor is h2 . a block of mass m is released from rest and slides down the track such that all frictional forces are considered to be negligible. the block leaves the track horizontally and strikes the ground at a distance d from the edge of the track as shown. which of the following statements is correct about the scenario? select two answers.
From the moment of release, until it hits the ground, there is an increase in mechanical energy. The two statements that describe how the block Earth's total mechanical energy stays constant are true. Both (3) and (4) are the right answers.
1) The block will land at a distance of 2D from the end of the track if it is released from a height of 2hi.
This assertion is untrue. The horizontal distance the block travels after leaving the track is influenced by the launch height (hi), even though it is not precisely proportional to 2hi. The horizontal distance D can be calculated using the rules of mechanical and energy conservation.
2) If the mass of the block is increased to 2M, the block will land 2D distance from the track's edge.
This assertion is untrue. The mass of the block has no bearing on the horizontal distance D that it travels after leaving the track.
3) From the time of release to the time the block hits the ground, the system's total mechanical energy, which only contains the block, grows.
This assertion is true. The system's overall mechanical energy rises when external factors like friction and air resistance are absent.
4) The block-Earth system's overall mechanical energy stays constant.
This assertion is true. As was already stated, the block-Earth system's total mechanical energy is conserved in the absence of outside forces like friction and air resistance. As the block descends the gradient and transforms into kinetic energy, its potential energy drops. The block's potential energy is further transformed into kinetic energy when it becomes a projectile after leaving the track.
Therefore, assertions (3) and (4) are true.
The total mechanical energy of the system, which just contains the block, increases from the time of release to the time it touches the ground. The total mechanical energy of the block-Earth system is constant.
To know more about the kinetic energy;
https://brainly.com/question/15764612
#SPJ12
The complete question is:
ON An inclined track is secured to a table. The height of the highest point of the track above the tabletop is hi. The height from the tabletop to the floor is k2. A block of mass M is released from rest and slides down the track such that all frictional forces are considered to be negligible. The black leaves the track horizontally and strikes the ground at a distance from the edge of the track as shown. Which of the following statements is correct about the scenario? Select two answers. if the block is released from a height of 2h1, the block will land at a distance 2D away from the end of the track. If the block's mass is increased to 2M, the block will land at a distance 2D away from the edge of the track The total mechanical energy of the system containing only the block increases from the moment of release to the moment it strikes the ground. The total mechanical energy of the block Earth system remains constant.
two point charges, a and b, are separated by a distance of 20.0 cm . the magnitude of the charge on a is twice that of the charge on b. if each charge exerts a force of magnitude 42.0 n on the other, find the magnitudes of the charges.
A and B are two point charges that are separated by 20.0 cm. The charge on an is twice as large also as charge on b in terms of magnitude. A force with magnitude 42.0 n, on the other hand, is equal to 2 x 0.7820 10-5C = 1.5640 10-5C.
The meaning of magnitudeAn average man would have given up given the size of the work. planetary science. Magnitude also describes how bright a star appears to be from Earth.
What does force magnitude mean in physics?The amount that encapsulates the force's strength is known as its magnitude. Consider the following scenario: the force is 10 N in the east. The direction is indicated by "towards east," while the force is indicated by "10." Magnitude can be thought of as simply the "value" or "amount" of the any physical quantity.
To know more about magnitude visit:
https://brainly.com/question/1447482
#SPJ4
consider a dark fine in an interfence pattern at which alomst no lightnery is arriving light from both slits is arrving at this point but the aves cancel where od3s the energy go
In this issue, it is stated that no light energy is entering a dark fringe inside an interference pattern. Our goal is to explain where the energy goes when this phenomena occurs.
What is energy?The definition of energy is "capacity to do work, which is ability to apply force creating displacement of an object." Energy simply refers to the force that moves objects, despite this definition's seeming complexity. Both potential and kinetic energy fall under this category.
In Example, how does energy function?There are various forms of energy. These consist of, among others, energy from nuclear , atomic energy, light, heat,, gravity, electrical, sound, chemistry.
To know more about energy visit:
https://brainly.com/question/2409175
#SPJ4
how does the vertical acceleration at point a compare to the vertical acceleration at point c?how does the vertical acceleration at point a compare to the vertical acceleration at point c?both accelerations are equal to zero.the acceleration at a is greater than that at c.the acceleration at a is less than that at c.both accelerations are equal to free fall acceleration.
When comparing the vertical acceleration at point a to the vertical acceleration at point, both accelerations are the same as the acceleration of free fall.
What is the difference between the vertical gravitational acceleration and this horizontal acceleration?The vertical acceleration generated by gravity is 9.8 m/s/s downward, but the horizontal velocity of a projectile is constant (a value that never changes). Each second, a projectile's vertical velocity changes by 9.8 m/s, yet its horizontal motion is unrelated to that of the projectile's vertical motion.
How do horizontal and vertical motion relate to one another?A projectile's vertical and horizontal motions are independent, meaning they have no bearing on one another. A projectile's two-dimensional motion can be broken down into its two 1-D motions, horizontal and vertical.
To know more about acceleration visit:-
https://brainly.com/question/12550364
#SPJ4
If it takes light 8⅓ minutes to travel from the Sun to Earth and if the Earth-Sun distance is 150,000,000 km, calculate the speed of light in meters per second. [Hint: First do side calculations to figure out how many seconds is equal to 8⅓ minutes and how many meters is equal to 150,000,000 km. Then divide the distance given in meters (m) by the time you found in seconds (s) to get the answer in units of m/s.]
The speed of light in metres per second is 300,000,000m/s
How to calculate speed?The speed of light can be calculated by dividing the distance moved by the time as follows:
Speed = distance (m) ÷ time (s)
According to this question, it takes light 8⅓ minutes to travel from the Sun to Earth and if the Earth-Sun distance is 150,000,000 km.
8⅓ minutes = 500 seconds150,000,000 km = 150000000000 metresThe speed of light can be calculated thus;
Speed = 150000000000m ÷ 500s
Speed = 300,000,000m/s
Learn more about speed at: https://brainly.com/question/394103
#SPJ1
one ball straight down, one down at angle, one sliding down on incline (frictionless) when do these objects hit the ground
If all objects were dropped from the same height and in a vacuum (no friction and no air resistance), then all three objects would hit the ground at the same time, regardless of their initial angle or tilt. This is because the only force acting on objects is gravity, which is a constant acceleration, causing all objects to fall at the same rate.
Gravity is the force of attraction between two masses. It's the reason things fall to the ground when they're dropped, and why planets orbit the sun. The strength of the gravitational force between two objects depends on their masses and the distance between them. The force of gravity is explained by the law of universal gravitation, which was first formulated by Sir Isaac Newton.
You can learn more about Gravity here brainly.com/question/14874038
#SPJ4
a horizontally directed 15-n force pushes a 5-kg block across the floor at a constant velocity what is the objects weight
The weight of the object is 5 kg x 9.8 m/s² = 49 N (Newtons), assuming standard acceleration due to gravity of 9.8 m/s². The horizontal force of 15 N is acting on the object at a constant velocity, so the net force on the object is 0 N, which means that the object is in a state of balanced forces.
Weight is a measure of the force of gravity acting on an object. It is determined by multiplying the mass of an object by the acceleration due to gravity, which is typically 9.8 m/s² on the surface of the Earth.
W = m x g
W = 5 kg x 9.8 m/s² = 49 N
Weight is a scalar quantity and is expressed in units of Newtons (N) or pounds. An object's weight is dependent on its mass and the strength of the gravitational field it is in. Objects with greater mass have greater weight, and the weight of an object decreases as it moves away from the center of a gravitational field, such as moving from the surface of the Earth to space.
Learn more about weight:
brainly.com/question/10069252
#SPJ4
in 1977 steve weldon ate 91 m of spaghetti in 29 s. at the same speed, how long would it take Mr. weldon to eat 5 m of spaghetti?
The time that would be taken is 1.6 s.
What is the speed?We know that the speed would be the ratio of the distance to the time that have been taken and that is how we would be able to solve the problem that we have in the case that is ahead of us in this question
We have that the speed is; Distance/Time
= 91 m/29s
= 3.1 m/s
At the same speed;
Time = Distance/Speed
= 5 m / 3.1 m/s
= 1.6 s
Hence we k now that the spaghetti would be able to take a time that is about 1.6 s
Learn more about speed:https://brainly.com/question/28224010
#SPJ1
draw a two-dimensional representation of a charged point object. specify a convenient x-y coordinate system to describe the electric field of the object in a plane
A hypothetical charge that is situated at a single location in space is a point charge.a scale of length used to describe an electron's size, can be used to classify an electron size even though it is frequently referred to as a point charge.
In an electric field, what exactly is a point charge?The area of space immediately surrounding a charged particle (also known as a point charge or a source charge) develops an electric field. The electric field version of Coulomb's Law is represented by this. In fact, the remainder of the cosmos is the area of space surrounding a charged particle.
We evaluate point charges for what reasons?Point charges in physics refer to bodies that are exceedingly small in size relative to their distance from one another. Due to how simple it is to determine the attraction force or repulsion between them, we therefore treat them as point charges.
To know more about point charges visit:
https://brainly.com/question/14531929
#SPJ4
which of the following is a longitudinal wave? which of the following is a longitudinal wave? light wave water wave sound waveradio wave
A sound wave is a longitudinal wave out of all 4 that is light wave, water wave, sound wave, radio wave.
What is longitudinal wave?Longitudinal waves are waves in which the medium's vibration is parallel to the wave's travel direction and the medium's displacement is in the same direction as the wave's propagation. A longitudinal wave is a form of wave in which the medium's vibration is parallel to the wave's direction and the medium's displacement is parallel to the wave's movement. The particles in a longitudinal wave are shifted parallel to the direction of the wave. Compressions travelling down a slinky are an example of longitudinal waves. By pushing and pulling the slinky horizontally, we may create a horizontal longitudinal wave.
To know more about longitudinal wave,
https://brainly.com/question/8497711
#SPJ4
n the above table, write whether each type of transistor will act as an open circuit or a closed circuit.
The p-type transistors in the preceding table can be used as a closed connection or as an external switch.
What is a P-type transistor?The p-type crystal serves as the n-p-n transistor's base. Base-collector junctions are typically forward-biased, but base-emitter junctions are reverse-biased, indicating the edit side of a junction has a larger concentration than the d e side.
A transistor of the kinds p and n is what?In a p-type microelectronic, the hole density is much higher than the electron density. The energy level of the p-acceptor type is close to the valency bond but far from the p-type semiconductor. an n-type semiconductor that has had an intrinsic semiconductor treated with phosphate or antimony.
To know more about transistor visit :
https://brainly.com/question/12530064
#SPJ4
A grinding wheel with radius of 20 cm is speed of 200 rpm when its power is cut off. It slows to a stop in 90s What was is the angular displacement of a point located at Yr? b) That is the angular displacement of a point located at r? Through what linear distance will the point at h travel? d) Through what linear distance will the point at travel? Before it was cut off, what was the period of one rotation?
The angular displacement of a point located at r is 7200π radians.
The angular displacement of a point located at Yr can be calculated using the formula: θ = ωₒt + (1/2)αt^2, where ωₒ is the initial angular velocity (in radians per second), t is the time it takes to come to rest, and α is the angular acceleration (in radians per second squared).
The initial angular velocity of the wheel can be calculated as ωₒ = 2πnₒ, where nₒ is the initial speed in revolutions per minute (RPM). We have nₒ = 200 RPM, so ωₒ = 2π * 200 / 60 = 40π radians per second.
The angular acceleration can be calculated as α = - ωₒ / t = - 40π / 90 = - 2π / 4.5 radians per second squared.
Plugging in the values, we get θ = 40π * 90 + (1/2)(-2π / 4.5) * 90²2 = 3600π radians.
The angular displacement of a point located at r can be calculated as θ = 2θ, since the distance traveled is twice as long. So, the angular displacement of a point located at r = 2θ = 2 * 3600π = 7200π radians.
The linear distance traveled by the point at h can be calculated as d = θ * Yr, where Yr is the radius of the wheel. Plugging in the values, we get d = 7200π * 20 cm = 144000π cm.
The period of one rotation before it was cut off can be calculated as T = 60 / nₒ = 60 / 200 = 0.3 seconds.
For more questions like Angular displacement visit the link below:
https://brainly.com/question/29258974
#SPJ4
A Crew Dragon capsule with a mass of 9,500 kg is reentering Earth's atmosphere. It has slowed down from orbital velocity to 2,000 m/s. Which of the following would be equal to the pull of the Earth on the capsule?
Group of answer choices
The push of air resistance on Earth
The gravitational pull of the capsule on the Earth
The gravitational pull of the sun on the capsule
The push of air resistance on the capsule
The capsule will be the push of air resistance on the capsule.
option D.
What is Newton's third law of motion?
Newton's third law of motion states that for every action force, there is an equal and opposite reaction force.
If the capsule is slowed down from orbital velocity to 2,000 m/s due to pull of the Earth on the capsule, then the capsule will exert equal and opposite force to Earth.
Thus, the opposite and equal force exerted by the capsule will be the push of air resistance on the capsule.
Learn more about Newton's third law of motion here: https://brainly.com/question/25998091
#SPJ1
The bracket is subjected to the two forces shown. Express each force in Cartesian vector form and then determine the resultant force FR.a) Find the magnitude of the resultant force.b) Find coordinate direction angle α of the resultant force.c) Find coordinate direction angle β of the resultant force.d) Find coordinate direction angle γ of the resultant force.Express your answers to three significant figures.
Each force in Cartesian vector form is (F1) ⃗ = (86.5 i + 186 j – 143k) N and (F2) ⃗ = (-220 i + 311 j + 220 k) N. The resultant force is (FR) ⃗ = (- 134i + 497j + 77k) N. a) The magnitude of the resultant force is 520 N. b) The coordinate direction angle α = 105. c) The coordinate direction angle β = 17.1. d) The coordinate direction angle γ = 81.5.
For a force vector (F,) ⃗ the direction angles made by vector with the x, y, and z are α, β, and γ and hence the Cartesian components of the vectors are given by:
Fx = F cos α
Fy = F cos β
Fz = F cos γ
The Cartesian vector form is given by: {Fx i + Fy j + Fz k}
According to the given data, (F1) ⃗ = 250N and (F2) ⃗ = 440N.
The factor vector (F1) ⃗ makes a 35 degree with xy plane. Hence, its projection on the xy plane will be F1 cos35. The projection makes a 25 degrees with the y-axis. Hence the y-component will be F1 cos35 cos 25 and x-component will be F1 cos 35 sin 25. Hence the (F1) ⃗ in cartesian form is given by:
(F1) ⃗ = 250(cos 35 sin 25 i + cos 35 cos 25 j – sin 35 k) N
(F1) ⃗ = (86.5 i + 186 j – 143k) N
Likewise,
(F2) ⃗ = 440 (cos 120 i + cos 45 j + cos 60 k) N
(F2) ⃗ = (-220 i + 311 j + 220 k) N
Hence, the resultant force is given by:
(FR) ⃗= (F1) ⃗+(F2) ⃗
(FR) ⃗ = (86.5 – 220)i + (186 + 311)j + (-143 + 220)k
(FR) ⃗ = (- 134i + 497j + 77k) N
a) The magnitude of the resultant force is given by:
FR = √(Fx^2+Fy^2+Fz^2 )
FR = √((-134)^2+497^2+77^2 )
FR = 520 N
The coordinate direction angles are:
b) cos α = Fx/FR = -134/520
α = 105
c) cos β = Fy/FR = 497/520
β = 17.1
d) cos γ = Fz/FR = 77/520
γ = 81.5
Learn more about Force vector:
https://brainly.com/question/13774406
#SPJ4
compute the skin depths for copper aluminum and gold at 1 ghz and 10 ghz and find the resistance of a 10 cm
The skin depth of a material at a given frequency is defined as the distance below the surface of the material at which the magnetic field inside it has decreased to 1/e (approximately 37%) of its surface value. The skin depth can be calculated using the following equation:
δ = (2 / μσf)^0.5
where μ is the magnetic permeability of the material, σ is the conductivity of the material, and f is the frequency.
For copper at 1 GHz, the skin depth is approximately 7.67 μm. For aluminum at 1 GHz, the skin depth is approximately 6.64 μm. For gold at 1 GHz, the skin depth is approximately 2.45 μm.
For copper at 10 GHz, the skin depth is approximately 2.38 μm. For aluminum at 10 GHz, the skin depth is approximately 2.10 μm. For gold at 10 GHz, the skin depth is approximately 0.78 μm.
The resistance of a 10 cm length of a material can be calculated using the following equation:
R = ρL / A
where ρ is the resistivity of the material, L is the length of the material, and A is the cross-sectional area of the material.
The above calculations are based on the assumption that the skin depth is much smaller than the dimensions of the material. In reality, the skin depth of a material can change with frequency and with temperature, so the above calculations are only approximate.
For such more question on skin depth
https://brainly.com/question/29976960
#SPJ4
Compute the magnitude of the resultant R of the forces exerted on the screw eye
The resultant R of the forces exerted on the screw eye is 357.77 lb.
What is force?The definition of force in physics is: The push or pull on a massed object changes its velocity. An external force is an agent that has the power to alter the resting or moving condition of a body. It has a direction and a magnitude.
A spring balance can be used to calculate the Force. The Newton is the SI unit of force.
The resultant R of the forces exerted on the screw eye = √(200² + 200² +2×200×200 × (3/5)) lb
= 357.77 lb
Learn more about force here:
https://brainly.com/question/26115859
#SPJ1
a 10-n falling object encounters 10 n of air resistance. the net force on it is a 10-n falling object encounters 10 n of air resistance. the net force on it is 6 n. 4 n. 0 n. 10 n.
The net force on the object is 0 N.
The total of all the forces operating on an item is defined as the net force.
A mass can be accelerated by net force. Another force acts on a body at rest or in motion. When there are a large number of forces in a system, the net force is utilised.
The larger the net force applying on the object, the faster it will move. These correlations are summarised by Newton's second law of motion.
The aforementioned acceleration equation may be modified to solve for net force as follows: Net Force = Mass * Acceleration, or F = m ×a.
The net force on a 10 N falling object that encounters 10 N of air resistance is 4 N.
The total force on the object is equal to the gravitational force minus the air resistance:
[tex]$$F_{\text{net}} = F_{\text{gravity}} - F_{\text{air resistance}} \\= 10 N - 10 N \\= 0 N$$[/tex]
For more questions on Net Force
https://brainly.com/question/14361879
#SPJ4